Cooler Master V8 Gts 82 Cfm Review
Libation Master V8 GTS CPU Cooler Review
Cooler Master adds all the same some other air cooler to the 5-series today - this time with the V8 GTS. Let'south take a shut wait at it and what it offers.
Introduction
Remembering dorsum to when I tested the V10 and the V6, I knew then that Cooler Master wasn't afraid to push the boundaries of what we would consider "normal" in air coolers for your CPU. Back in that time, they were experimenting with TEC assisted cooling, similar what was delivered in the V10, and they were as well very keen to supply all of the 5-series coolers with a black plastic shroud hoping to inspire the wait of an engine sitting in the middle of your PC. A few things that stick to every cooler in the series is that you volition find aggressive styling with angular lines and red LED lighting, the black, red, and silver coloring of each of them, and that well-nigh of these coolers, minus the V8, shipped with a pair of fans to help remove more heat than the typical solutions from other manufacturers.
Getting back to why we are here today, we are nigh to see the latest take on the V8 released a couple years ago. With the V8 in that location were four towers of fins, a staggering 8 heat pipes and 180W TDP support. The pattern team over at Libation Principal thought to themselves what would happen if we took the Vapor Bedchamber technology we were working on with the TPC coolers, and try that in the V-series? They also took considerations with the design to allow for much better retentivity clearance, and have besides included a new hardware kit to mount this new design, just honestly, these are some of the more mundane things almost this new libation.
Cooler Master brought us hither today to look at the V8 GTS. This refresh of an old design has been completely redesigned from head to toe with only hints of the original V8. 4 towers have been reduced to three, the unmarried fan of the V8 has been doubled so that the V8 GTS has plenty of air flow, it keeps eight heat pipes, simply his time offers a TDP of 250W since the Horizontal Vapor Chamber used in this design allows hot spots from the CPU to even out, and also allows all 8 pipes a way to transfer the heat since eight pipes in a base is way too large to work on a CPU IHS.
I am pretty sure that with this listing of features and the newer estrus rating, we may very well be looking at the new top dog from Cooler Master, but y'all volition just have to keep reading to find that out.
Specifications, Availability and Pricing
As yous can see by scanning the nautical chart provided by Cooler Primary above, the V8 GTS will accommodate whatsoever Intel socket since LGA775, and will do the same with AMD since socket AM2. Overall the cooler is 154mm alpine, 149.8mm broad and 166.5mm wide from intake to frazzle. The belfry is comprised of a large plastic shroud, the Vapor Chamber, eight 6mm bore copper oestrus pipes, and 45 aluminum fins in the main stack and 37 aluminum fins in each of the smaller stacks. In total, fans included, the V8 GTS weighs in at 854 grams, or simply near two pounds.
The pair of fans that ship with this cooler are A14025-16CB-4FBP-F1 140mm fans that were made specifically for this cooler, since one of these fan frames even sports the V8 GTS name molded into it. These fans spin on the fourth generation of POM bearings, and are capable of speeds of 600 to 1600 RPM to allow you to dial in the noise levels. These 20mm thick fans are capable of delivering up to 82 CFM each, while pushing one.45mmH20 of static pressure level to try to go the air flow through all 3 fin stacks. Lastly these fans are PWM controlled, but they can depict up to 3.72W of power, so proceed that in mind if you are using an boilerplate fan controller - you may exceed the channels capabilities.
There is an NDA on this product every bit I tested and wrote information technology upward, and that expires today. I would assume you will be able to locate the cooler at that time only from Cooler Master directly, just within a week or two, the V8 GTS should offset to arrive on shelves. With all that Libation Chief has incorporated into this cooler design, the price is a bit weighty and may be a little tough to bear for some.
I am told that the MSRP has been set to $99.99, and while a few locations may stick to that number, expect others to do a fleck of gouging to accept the price well over $100 even before taxes or shipping has been practical. The real question now, is can it hang with other $100 air cooling solutions, or was that money spent to make it look pretty instead? Allow's notice out over the next few pages.
Packaging
The V8 GTS comes in some very attractive packaging. On the forepart is the "chromed" company proper name and the production name near the bottom, along with a large image of the powered libation. It also points out at the bottom that this libation uses Vapor Chamber tech, offers maximum cooling performance, and has a super long life begetting on the 140mm fans.
The next panel offers some other angle to view the V8 GTS, but this fourth dimension near the bottom Cooler Chief places the socket compatibility lists.
The back offers information about the triple tower, its eight pipes and cooling performance; it also addresses the Horizontal Vapor Chamber, and finishes with information on the bearing and the 160,000 hours of life to the fans. This is all and so repeated in seven other languages, earlier you lot encounter the dimensional drawings at the bottom.
The concluding panel on the packaging uses the majestic background we always see with Cooler Master products, and on it you volition find the specifications chart that we covered on the final folio.
Inside of the box yous will observe the white hardware box showtime. Subsequently removing that you tin pull the top half of the dumbo foam inner packaging to remove the cooler. Yous can tell from the earlier images that the box took a pretty skillful hitting in transit, but due to the two piece of foam surrounding the cooler, there was no damage to the cooler - it arrived in perfect condition.
Cooler Master V8 GTS CPU Libation
Looking at the V8 GTS from the side that will be nearest the GPU, you come across a T-shaped shroud that holds the pair of fans between the trio of fins stacks. You also tin can see the rut pipage system of two to the left stack, iv in the middle stack, and again, two to the right fin stack.
This is the intake side of the V8 GTS. As you can see, air is drawn through the smaller stack, with the 140mm fan assuasive for a bit of pre-cooling with the two pipes delivering oestrus to the 37 fins of this section of the cooler, before that fan blows on the main stack.
The V8 GTS is now in a position as if nosotros were able to see it from the meridian once installed. You lot tin see both sides are identical, just there is a pair of iv-pin PWM fan power leads connected to a Y-splitter to ability the fans on this side of the cooler.
That leaves u.s.a. with the frazzle side of the V8 GTS. So, once the air has passed the pre-cooler, pushed through the chief stack with the start 140mm fan, then afterward the primary stack another 140mm fan is sucking air from the cooler and pushing its flow over the concluding of the three fin stacks.
If any of that was besides disruptive, I went alee and removed the shroud and fans so that you could go an unimpeded view of the fin and piping system.
Nether the cooler, where the heat pipes originate under, is the fan support and mounting top plate. The grooves at the elevation back up a plastic post on both fans, and the whole at both ends is to allow a screw through to secure legs to the base.
With the heat pipes soldered to the top plate, and to this base of operations, thermal conduction is increased. If they had gone with a copper base here instead of the large Horizontal Vapor Chamber seen hither, eight pipes would take been likewise much without a fashion to evenly spread the CPU heat into those wide spread 48mm of just rut pipes. The base is flat confronting a razor, and fifty-fifty with the sticker still on, y'all tin run into the roughness of the milling.
Accessories and Documentation
Inside of the plain white box you observe atop the cooler, you will find two back plates. The one on the left is universal for all Intel sockets except LGA2011. To the right is the AMD back plate that has been isolated under it to protect things from shorting out.
You will also find 3 sets of legs for the coolers base of operations, and a pair of screws to mountain the appropriate gear up. To the left are the long AMD brackets to marshal the libation one way, and next to it are the shorter ones to allow the cooler to blow left to right, rather than lesser to elevation. That leaves the universal Intel legs to the correct.
Upward in front in this epitome above you have the open and closed ended wrench to aid in the mounting of the cooler, and just behind is a tube of Thermal Fusion paste to employ with your cooler. The back row has the acme mounting nuts to the left, and on the correct are four things labelled as "screws" and fifty-fifty though the renderings don't show it, I believe they are for AMD sockets.
Hither we have the LGA 2011 risers for the superlative of the socket, the universal risers for Intel with the pre-applied nylon washers on the lesser of them so they don't scuff the motherboard. The washers on the sheet to the right are for AMD mounting, again to protect the motherboard.
While I had the shroud off and one of the fans dismounted from it, I figured I would snap this paradigm of the sticker on the back of it. Along with the number I rattled off in the specifications, there is the DF1402512SEHN naming every bit well.
The paperwork is broken down into iii sections. At acme left is the multi-lingual user manual for the V8 GTS. The larger ane to the correct is strictly English language instructions, leaving the largest one in the image, the information and terms of the two year warranty.
Installation and Finished Product
For Intel, afterwards you lot set each of the ends to the proper notch for your socket type, mine existence the center of three, you just drop it in on the back of the lath. No need to worry about the screws or anything no matter which management it is installed.
Once the back plate and its iv threaded posts are aligned in the holes, you lot but tighten the knurled nuts to the peak of them making the back plate at present function of the motherboard.
You too volition need to pigsty the appropriate legs under the acme piece of the base to secure them. The threads are in the sets of legs, non in the aluminum the screw is running through.
Later on working but a bit in shut quarters to secure the top nuts to keep the legs secured to the board, the cooler is finally installed. Since the pre-libation is so modest and raised up from the base, it allows for 50mm of retention and oestrus spreader to hands laissez passer under its fins.
From the top of the board, not only tin can yous put large heat spreaders in here without blocking much of the cooler, all four slots are easily accessible, and the same can be said on the opposing side for LGA2011 users that desire to populate all of the slots.
With the board now in the test chassis, the V8 GTS is large and in charge from this angle. It covers the view of almost everything, merely as I showed you, you tin can all the same access the retentivity slots, and admission to the 8-pin is generous as well. But wait, it gets amend.
We at present have the V8 GTS in her illuminated glory. Both of the 140mm fans offer four red LEDs in each fan, and the shroud offers six lined up at the top for a total of 14 LEDs illuminating the components that surround this very bonny looking design.
The Test System and Thermal Results
I would get-go like to give thanks HIS, GIGABYTE , InWin and AVADirect for supplying products for me to examination with.
Testing for the CPU coolers is washed with the use of RealTemp to ascertain temperatures, Intel Burn down Examination to deliver the load to the CPU and CPU-Z to verify the CPU speed and the voltage beingness used in Windows. All of the testing is washed with an ambient temperature of 24.5-25C and humidity is maintained to 35% sometimes less.
For the "stock" runs, information technology's more of a plug and play setup where the PWM of the motherboard is in control of the fans speeds for both the idle and load results. Speed Step is active and the processor idles at 1600 MHz and loads at 3500 MHz for the stock settings. I likewise set the memory to run at 1600 MHz for stock. As for the overclocked runs, I load the CPU at four.5 GHz and idle results are obtained with vii.5V to the fans while the load run is set up to deliver 12V to the fans. This allows me to guess the lowest and highest fan ratings for my charts.
You will also see that the charts have been slightly adjusted. From now on I will mention the idle temperatures if there is something worth noting other than an boilerplate of xx-five to 20-seven degrees equally the PWM controls and Speed Step allow for nearly ambience results in most instances. What you are now getting is a stock speed loaded temperature chart and an overclocked loaded temperature chart. To clean up the sound results, I as well removed all of the fans that aren't on the thermal charts. If you want to compare those results to new coolers, the onetime chart is still available in the older reviews.
While the 50 degree outcome looks mediocre in the stock testing nautical chart, await closer. It is merely half-dozen degrees behind the best solution I have tested, and a mere degree backside some of the best air cooler money can buy.
With the Intel 2600K CPU pushing almost 125W of heat load, you can meet the V8 GTS has fallen a fleck in the efficiency it shows at stock levels. 73 degrees is a good upshot, but against the best air cooler, the V8 GTS falls five degrees away from the top results in air cooling. Still, beauteous results and functioning levels anyone can appreciate.
Noise Level Results
When I gathered the 34dB result for the stock runs, I was monitoring the speeds, and with 1055 RPM, this is the outcome I saw on the meter. Not likewise shabby because that this is actually merely a barely audible hum at this level.
When nosotros moved over to the overclocked runs and allowed the motherboard to evangelize 12V to the pair of fans, I could easily hear them from across the office. With the fans now showing 1603 RPM in AIDA64, I took out the meter and saw the 58dB reading, shown in the nautical chart above.
Final Thoughts
The V8 GTS is really the all-time of all worlds. You lot get much amend than boilerplate operation out of the cooler, and it isn't the typical tower cooler that looks plain and boring, but rather a very unique design that will expect good in any build, specially all of those red and black themed builds out in that location. Having the thought to apply so many oestrus pipes needs a new way of thinking as to how to deliver the estrus into each of them, and with the Horizontal Vapor Chamber, information technology not only looks adept, but it is super efficient at getting the rut from the CPU and into the menstruation of the pair of 140mm fans.
At that place are a lot of features that make the V8 GTS an obvious choice - like aesthetics, uniqueness, functioning, fifty-fifty the massive amount of retention clearance, but that is non to say there aren't trivial things that need considered. Mounting the cooler is largely a pain in the barrel, just once you become through the trouble of mounting the V8 GTS, you tin be sure the cooler volition go nowhere, every bit information technology really becomes i with the motherboard. There is also the racket factor to take into consideration. While most times with the PWM roofing your cooling needs, you won't see the loftier results I got with my overclocked runs, only yet, at 58dB the cooler is quite loud and is something you will accept to deal with. The last thing was constitute when I actually powered the libation. I had some issues getting the fans in and out at first, only didn't think much of it. Come to find out, that hit the cooler took in transit really bent in the showtime pre-cooler stack, and the fan did rub on the fins until I adapted said fin stack. Only little things, that aren't great detractors of a purchase, but just things I idea you should be aware of.
In the finish, fifty-fifty though there are more than efficient solutions to buy at $100, the Cooler Master V8 GTS even so wins me over. While not the greatest performer on the list, placing in the top 10 air cooling solutions I have tested is no piece of cake accomplishment. As I said, you can become better cooling, but nothing that looks this good, and as a signal of fact, with the Thermalright coolers listed, likewise every bit a few of the others, retentivity clearance is a definite effect with those. Every bit for the Thermaltake and Noctua solutions, they are cheaper, simply none of them look as proficient as the V8 GTS volition in your rig. I do think this cooler could seek much better at a price bespeak near $fourscore, but that huge vapor sleeping room along with a triple set of fin stacks, while still offer users great access to their memory is notwithstanding a laudable feat, fifty-fifty if a touch the pricy side of things.
At the terminate of all of the thought and consideration, I really practise recollect Cooler Main is stepping upwards their game since the original concept of the V8, also every bit improving on what the TPC 812 had to offer, and if you tin afford this cooler, I know you lot are going to honey it once installed in your PC.
Source: https://www.tweaktown.com/reviews/5598/cooler-master-v8-gts-cpu-cooler-review/index.html
0 Response to "Cooler Master V8 Gts 82 Cfm Review"
Post a Comment